Du line Dupline(R) Master Module Type G 2196 00.. (R) Fieldbus Installationbus Dupline(R) Channel Generator 128 signals and DC power supply on 3 wires RS 485 port for interfacing to control system Automatic communication with specific PLC's/Controllers Multidropping of up to 16 G 2196 0000 or G 2196 0005 on RS 485 * Cost-effective design on open PCB (86 x 54 mm) * LED-indications for supply, Dupline(R) carrier and RS 485 Tx * DC-supply * * * * * Product Description G 2196 00.. is a combined module on open printed circuit board. The unit performs three functions: Dupline(R) channel generator, power supply synchronization (enables 3-wire system with supply) and RS 485 interface. It has been designed as a cost-effective solution for multiplexing the push-button and lamp signals in elevators. Ordering Key The standard version of the Master Module has a generalpurpose RS 485-protocol available, but to facilitate the interfacing easy, special protocol versions of the master module for automatic communication with specific PLC's/ Controllers are developed continouosly. These are listed under "Type Selection". G 2196 0000 700 (R) Type: Dupline Open PCB Combined module Interface type DC supply Type Selection Supply PLC Interface type Ordering no. PLC Interface type Ordering no. 20-30 VDC 20-30 VDC 20-30 VDC Standard protocol Lucky Goldstar K-series GE-Fanuc 90-30 series G 2196 0000 700 G 2196 0001 700 G 2196 0002 700 Mitsubishi FX- and A-series Omron Modbus RTU Slave G 2196 0003 700 G 2196 0004 700 G 2196 0005 700 Input/Output Specifications Supply Specifications Power output Output voltage Output current Short circuit protection Output voltage drop Dupline(R) carrier Output voltage Current Short circuit protection Scan time 128 channels 64 channels RS 485 communication port Communication speed Connection Pin assignment Data line + (B) Data line - (A) 5 VDC supply + 5 VDC GND Current load 5 VDC supply Dielectric voltage RS 485 port - Dupline(R) Settings Device no. (for RS 485) (only G 2196 0000) 64 or 128 channels Power supply Operational voltage (Vin) Reverse polarity protection Current consumption Power dissipation Inrush current Transient protection voltage Dieelectric voltage Supply - Dupline(R) Supply - RS 485 port 20-30 VDC (pulsating) < 4.0 A @ 25C 4 A quick acting fuse < 1.0 V 8.2 V (pulsating) < 40 mA Yes 132.2 ms 69.8 ms Overvoltage cat. III (IEC 60664) 20-30 VDC None < 100 mA <6W < 200 mA 800 V None > 2 kVAC (rms) 19200 Baud 9 pole female SUB-D Pin 3 Pin 8 Pin 6 Pin 5 < 150 mA > 2 kVAC (rms) 4 DIP-switches 1 DIP-switch Specifications are subject to change without notice (29.04.03) Dupline(R) is a registered trademark. A product of the CARLO GAVAZZI Group 1 Du line G 2196 00.. (R) Fieldbus Wiring Diagram General Specifications Power ON delay Indication for RS 485 Tx Supply ON Dupline(R) carrier Environment Pollution degree Operating temperature Storage temperature Humidity (non-condensing) Mechanical resistance Shock Vibration Dimensions Installationbus 2s LED, red LED, green LED, yellow Lift Controller RS 485 G 2196 00.. 123 45 2 (IEC 60664) 0 to +50C (+32 to +122F) -50 to +85C (-58 to +185F) 20 to 80% 15 G (11 ms) 2 G (6 to 55 Hz) 86 x 54 mm open printed circuit board, 4.2 mm hole in each corner for mounting 100 g Weight ~ = +n floor 3. floor Car panel 2. floor DIP-switch Setting for G21960000700 1. floor 23 2 GND Signal Power ON 1 2 The device no. and number of Dupline(R) channels are selected by means of 5 DIP-switches. 3 4 SW ON 1-4 5 Terminal OFF 1 2 3 4 5 Device no. 5 64 ch. 128 ch. Accessories Function GND Dupline(R) Signal Power Out GND DC Power Supply Data brochure DAT DMM (RS 485 protocol specification and design hints) Mode of Operation The G 219600.. Dupline(R) master module (DMM) is part of the Dupline(R) concept for multiplexing the push-button and lamp signals in elevators. As shown on the wiring diagram a 3-wire bus with signal, DCpower and common GND goes throughout the shaft to all the push-button panels and floor indicators, and to the car. The DMM is connected to a standard DC-supply which it synchronizes with the Dupline(R) carrier signal before it is output to supply the push-button panels. The synchronization is necessary in order to enable 2 the Dupline(R) and DC-supply to share the GND-wire. The most cost-effective way to interface the elevator controller to the master module is to make use of the RS 485 port (see wiring diagram). In this way, the size and the number of controller I/O-board(s) can be reduced significantly, since the I/O-terminals for lamps, pushbuttons and floor-indicators are no longer needed. Based on requests from customers, special versions of the master module for automatic communication with specific PLC's/Controllers are developed continuously. This makes the interfacing very easy, since these devices automatically transfer the Dupline(R) data to/ from the internal memory of the PLC/ Controller. The versions available for the moment are listed under "Type Selection". More detailed information about interfacing to the individual PLC-types are available. The standard version G 2196 0000 700 utilizes a general purpose protocol for implementation in any PLC/Controller software. In this case, the communication is not automatic, since it must be driven from the application software. Another way to implement the elevator controller interface is to make hardwired connections between the I/O's of the controller and Dupline(R)-modules positioned next to it, thus making use of the peer-to-peer communication capability of Dupline(R). This solution is less cost-effective, but highly flexible since existing and different control-systems can be used. Specifications are subject to change without notice (28.09.99) Dupline(R) is a registered trademark. A product of the CARLO GAVAZZI Group