E3Z 1
Photoelectric Sensor with Built-in Amplifier
E3Z
For almost all binaray-detection applications,
you can make selection from the E3Z
Features
Basic
performance
Reliability
East-to-
operate
Environmental
protection
Globalization
Photoelectric Sen-
sor with built-in am-
plifier is applicable
to a wide variety of
lines and ensures a
longer sensing dis-
tance than any other
model.
Basic performance
Lineup of models corre-
sponding to applications
(thin beam, transparent,
grooved)
Through-beam Model
Retroreflective model
(with MSR function)
15m
Diffuse-reflective model
1m
4m
Dimensions 10.4mm 20mm
31mm
Distance-setting model
0.2m
2Photoelectric Sensors
Meets a variety of
international stan-
dards, thus allowing
use in any country.
Global network with 191 offices in 38 countries. M8-connector, PNP output types that meet
international standards are available.
User-friendly Pho-
toelectric Sensor
takes all installation
and on-site condi-
tions into consider-
ation.
A general-purpose connector ensures easy on-
site installation!
The compact and space-saving model can be
installed in any location.
Eliminates the influ-
ence of installation
and on-site condi-
tions, thus increas-
ing the reliability of
the line.
Highly water and dust-resistive and ensures
easy installation in any location.
Resists common-mode noise generated by in-
verters.
E3Z-series reliabili-
ty covers a wide
range of object/
background combi-
nations, and ensure
stable detection re-
gardless of work-
piece color or
glossiness.
Globalization
Easy-to-operate
Our conventional product
Reliability
IEC60529 IP67
0
20
40
60
80
100
120
3 10 100
Inverter frequency (kHz)
Inverter noise voltage (V)
OMRON 's conventional E3V3
E3Z
Stability
3E3Z
Photoelectric Sen-
sor with Built-in Am-
plifier
Earth-friendly energy-saving type.
10-quantity packing reduces waste cartons. Packed in "combustible" polyethylene bags
free of Styrofoam. *
Standard models provided with a 0.5-m cable are
available for the elimination of unnecessary ca-
ble length.
On-going elimination of materials containing
lead.
Ideal for detecting
small objects with a
small spot:
● Tiny objects as little as
0.1 mm in diameter can
be detected with a
2.5-mm dia. spot.
● A thin beam enables de-
tection through a gap or
small hole.
● The small spot of light en-
ables visual checking of
sensing spot position.
Environmental
protection
This ECO label is indicated on
products that meet the environmental
standards established by OMRON.
E3Z
Power Consumption Comparison
Conventional sensor
Approx.
30 % less
Saves energy *
* The above figure is based on measurement under normal operating conditions.
Recycled paper is used.
* If this bag is burned, dioxin hazardous to humans is
hardly generated.
0.5m type
2m type
Unnecessary cable length
Uses environmentally friendly, lead-free solder.
eco
Pb
Narrow Beam
model
4Photoelectric Sensors
Stable detection of
thin-wall PET
bottles adequate for
recycling
Standard-size
transparent object
sensor
● Uses OMRON's unique
optical system ("Inner
View") that can detect
various shapes of PET
bottles and transparent
objects.
● Detects a wide range of bott-
les from 500-ml bottles to
2-l bottles, and from single
bottles to sets of stocked
bottles.
Grooved design
eliminates the need
for optical axis
adjustment.
●Two-axis models also
available..
Transparent
PET bottles
Reduced
adjustment
5E3Z
Applications
E3Z-LS background and foreground suppression models
Detecting covers on cosmetic products Detecting pastries on conveyor belts Detecting packaged chewing gum or candy
E3Z-L narrow beam models
Checking for straws Determining front/back or orientation of
floppy disks
Detecting uneven joints
E3Z-B transparent object model
Transparent PET Bottle-related Detection
- One bottle
Transparent PET Bottle related Detection
- Multiple bottles (Stocker)
Detection of films and glass plates
E3Z-G grooved type model
Crane and automated warehouse conveyor table passage inspection and positioning.
(Sensing at angle)
(Enlargement)
Back
Front
Grooved-Type
Photoelectric Sensor
E3Z-G
6Photoelectric Sensors
Ordering Information
Sensors
Accessories (Order Separately)
Slits
Sensor I/O Connectors
Sensor type Shape Connection method Sensing distance Model
NPN output PNP output
Through-beam
Pre-wired models
(2 m)*3 E3Z-T61 E3Z-T81
Connector type E3Z-T66 E3Z-T86
Pre-wired models
(2 m)*3 E3Z-T61A E3Z-T81A
Connector type E3Z-T66A E3Z-T86A
Retroreflective
model (with M.S.R.
function)
*1
*1. Not attached. Please purchase the optional reflector (9 types) according to your application.
Pre-wired (2 m)*3 *2
*2. The sensing distance specified is possible when the E39-R1S used. Figure in parentheses indicate the minimum required distance between the Sensor and Re-
flector.
E3Z-R61 E3Z-R81
Connector type E3Z-R66 E3Z-R86
Diffuse-reflective
Pre-wired models
(2 m)*3
*3. Models provided with a 0.5-m cable are available. When ordering, specify the cable length by adding the code "0.5M" to the model number (e.g., E3Z-T61 0.5M).
E3Z-D61 E3Z-D81
Connector type E3Z-D66 E3Z-D86
Pre-wired models
(2 m)*3, *4
*4. The connector joint type is available M12. Its model ends with -M1. (Example: E3Z-T61-M1J)
E3Z-D62 E3Z-D82
Connector type E3Z-D67 E3Z-D87
Thin beam type
reflective model
Pre-wired models
(2 m)*3 E3Z-L61 E3Z-L81
Connector type E3Z-L66 E3Z-L86
Distance-settable
Pre-wired models
(2 m)*3 E3Z-LS61 E3Z-LS81
Connector type E3Z-LS66 E3Z-LS86
Transparent PET
bottle type Retro- re-
flective model (with-
out M.S.R. function) *1
Pre-wired (2 m)
*3 *2 E3Z-B61 E3Z-B81
Connector type E3Z-B66 E3Z-B86
Pre-wired models
(2 m)
*3 *2 E3Z-B62 E3Z-B82
Connector type E3Z-B67 E3Z-B87
Grooved type
through-beam
model
1
Pre-wired models
(2 m)
*3
E3Z-G61 E3Z-G81
2
E3Z-G62 E3Z-G82
1
Junction connector E3Z-G61-M3J E3Z-G81-M3J
2
E3Z-G62-M3J E3Z-G82-M3J
Slit width Sensing distance (typical) Minimum sensing object (typical) Model Quantity
E3Z-T## E3Z-T##A
0.5 mm dia. 50 mm 35 mm 0.2 mm dia. E39-S65A
One set (contains slits for both
the emitter and receiver)
1-mm dia. 200 mm 150 mm 0.4 mm dia. E39-S65B
2-mm dia. 800 mm 550 mm 0.7 mm dia. E39-S65C
0.5 x 10 mm 1 m 700 mm 0.2 mm dia. E39-S65D
1 x 10 mm 2.2 m 1.5 m 0.5 mm dia. E39-S65E
2 x 10 mm 5 m 3.5 m 0.8 mm dia. E39-S65F
Size Cable type Shape Cable length Model
M8
Standard cable
2 m
4-wire type
XS3F-M421-402-A
5 m XS3F-M421-405-A
2 m XS3F-M422-402-A
5 m XS3F-M422-405-A
M12 (for -M1J)
2 m
3-wire type
XS2F-D421-DC0-A
5 m XS2F-D421-GC0-A
2 m XS2F-D422-DC0-A
5 m XS2F-D422-GC0-A
Red light Infrared light
15m
10m
4m
[100mm]
5 to 100 mm (wide view)
1m
90±30mm
40 mm20 mm 200 mm
BGS (at min. setting)
BGS (at max. setting)
FGS (at max. setting)
FGS (at min. setting)
Incident
light level
threshold (fixed)
500mm [80mm]
2m [100mm]
25mm
Straight
L-shaped
Straight
L-shaped
7E3Z
Reflectors
Not provided with retroreflective models
* Values in parentheses indicate the minimum required distance between the sensor and reflector.
Note: 1 .When using the reflector of other than the rated value, set the sensing distance to about 0.7 times of the typical example as a guideline.
2 .For details, refer to the "Reflector list".
Mutual interference prevention filter
Mounting Brackets
Note: 1 .If a through-beam model is used, order two Mounting Brackets for the emitter and receiver respectively.
2 .For details, refer to the "Mounting bracket list".
Name Sensing distance (typical) * Model Quantity Remarks
Reflectors
3 m [100 mm] (Rated value) E39-R1 1
4 m [100 mm] (Rated value) E39-R1S 1
500 mm [80 mm] E39-R1S 1 for E3Z-B#1/6
2 m [100 mm] for E3Z-B#2/7
5 m [100 mm] E39-R2 1
2.5 m [100 mm] E39-R9 1
3.5 m [100 mm] E39-R10 1
Fog preventing 500 mm [80 mm] E39-R1K 1 for E3Z-B#1/6
2 m [100 mm] for E3Z-B#2/7
Small reflector 1.5 m [50 mm] E39-R3 1
Tape Reflector
700 mm [150 mm] E39-RS1 1
1.1 m [150 mm] E39-RS2 1
1.4 m [150 mm] E39-RS3 1
Sensing distance Shape/dimensions Model Quantity Remarks
3 m E39-E11
2 sets each for emit-
ters and receivers
(total of 4 pcs.)
Can be used with the through-beam E3Z-T##A.
The arrow represents the polarizing direction.
Changing the polarizing direction of the two adja-
cent emitters and receivers prevents mutual in-
terference.
Shape Model Quantity Remarks Shape Model Quantity Remarks
E39-L153 1
Mounting Brackets E39-L150 One set
Sensor adjuster
Easy mounting to alumi-
num frame/rail of conveyor
or like, easy adjustment.
For left-to-right adjustment
E39-L104 1
E39-L43 1 Horizontal type mounting
bracket E39-L151 One set
E39-L142 1
Horizontal type protective
cover bracket
E39-L93 One set
Sensor adjuster
Easy mounting to alumi-
num frame/rail of conveyor
or like, easy adjustment.
For vertical angle adjust-
ment
E39-L44 1 Rear mounting bracket
E39-L98 1 Protective cover bracket E39-L144 1 Vertical protective cover
bracket
0.2
1
4.9
10.8
7.4
11.231.4
8Photoelectric Sensors
Rating/performance
* Values in parentheses indicate the minimum required distance between the sensor and reflector.
Sensor type Through-beam Retroreflective
model (with M.S.R.
function)
Diffuse-reflective
wide-beam
Model
NPN output
E3Z-T61/T66 E3Z-T61A/T66A E3Z-R61/R66 E3Z-D61/D66 E3Z-D62/D67
Item PNP output E3Z-T81/T86 E3Z-T81A/T86A E3Z-R81/R86 E3Z-D81/D86 E3Z-D82/D87
Sensing distance 15 m 10 m 4 m (100 mm) *
(When using the
E39-R1S)
3 m (100 mm) *
(When using the
E39-R1)
100 mm (White
paper 100 x 100
mm)
1 m (White paper
300 x 300 mm)
Setting range ---
Reflectivity characteristic ---
Spot Diameter ---
Standard sensing object Opaque: 12-mm dia. min. Opaque: 75-mm dia.
min.
---
Min. sensing object ---
Differential distance --- 20% max. of sensing distance
Directional angle Both emitter and
receiver: 3° to 15°
Both emitter and
receiver: 3° to 5°
2° to 10° ---
Light source (wave length) Infrared LED
(860 nm)
Red LED
(700 nm)
Red LED
(680 nm)
Infrared LED
(860 nm)
Power supply voltage 12 to 24 VDC ±10%, ripple (p-p) : 10% max.
Current consumption emitter: 15 mA receiver: 20 mA 30 mA max.
Control output Load power supply voltage 26.4 VDC max., load current 100 mA max. (residual voltage 1 V max.) Open
collector output type (depends on the NPN/PNP output format) Light-ON/Dark-ON switch selectable
BGS / FGS selection ---
Protective circuits Protection from load short-circuit and
reversed power supply connection
Reverse polarity protection, output short-circuit protection,
mutual interference prevention
Response time Operation or reset: 1 ms max.
Sensitivity adjustment Single-turn adjustment
Ambient illuminance Incandescent lamp: 3,000 lux max. Sunlight 10,000 lux max.
Ambient temperature Operating: -25°C to 55°C, Storage: -40°C to 70°C (with no icing or condensation)
Ambient humidity Operating: 35% to 85% RH, Storage: 35% to 95% RH (with no icing or condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC at 50/60 Hz for 1 minute
9E3Z
Rating/performance
Diffuse-
reflective Distance-
settable
Retro-reflective for PET bottles
(without MSR function) Grooved-type
narrow-beam wide-beam
E3Z-L61/66 E3Z-LS61/66 E3Z-B61/66 E3Z-B62/67 E3Z-G61 E3Z-G62
E3Z-L81/86 E3Z-LS81/86 E3Z-B81/86 E3Z-B82/87 E3Z-G81 E3Z-G82
90 ± 30 mm
(White paper
100 x 100 mm)
BGS: White or black paper (100 x 100 mm):
20 mm to set distance
FGS: White paper (100 x 100 mm):
Set distance to 200 mm min.
Black paper (100 x 100 mm): Set distance to
160 mm min.
500 mm
(80 mm) *
(When using the
E39-R1S)
2 m (100 mm) *
(When using the
E39-R1S)
25 mm
1 optical axis 2 optical axis
--- White paper (100 x 100 mm): 40 to 200 mm
Black paper (100 x 100 mm): 40 to 160 mm
---
Refer to
the diagram
„Hysteresis
Difference vs.
Sensing
Distance“
Black/white-error:
10% of set distance max.
---
2.5 mm dia.
(when sensing
distance is
90 mm)
---
--- Transparent round PET bottle
500 ml (65 mm dia.)
---
0.1 mm dia.
(copper wire)
---
---
Red LED
(660 nm)
Red LED
(680 nm)
Red LED
(680 nm)
Infrared LED
(860 nm)
12 to 24 VDC ±10%, ripple (p-p) : 10% max.
30 mA max 25 mA max. 40 mA max.
Load power supply voltage 26.4 VDC max., load current 100 mA max. (residual voltage 1 V max.) Open collector output type
(depends on the NPN/PNP output format) Light-ON/Dark-ON switch selectable
--- BGS: Open or connected to GND
FGS: Connected to Vcc
---
Reverse polarity protection, output short-circuit protection, mutual interference prevention
Operation or reset: 1 ms max.
Single-turn
adjustment
five-turn endless adjuster Single-turn adjustment ---
Incandescent lamp: 3,000 lux max. Sunlight 10,000 lux max.
Operating: -25°C to 55°C, Storage: -40°C to 70°C (with no icing or condensation)
Operating: 35% to 85% RH, Storage: 35% to 95% RH (with no icing or condensation)
20 MΩ min. at 500 VDC
1,000 VAC at 50/60 Hz for 1 minute
10 Photoelectric Sensors
Rating/performance
Sensor type Through-beam Retroreflective
model (with M.S.R.
function)
Diffuse-reflective
wide-beam
Model
NPN output
E3Z-T61/T66 E3Z-T61A/T66A E3Z-R61/R66 E3Z-D61/D66 E3Z-D62/D67
Item PNP output E3Z-T81/T86 E3Z-T81A/T86A E3Z-R81/R86 E3Z-D81/D86 E3Z-D82/D87
Vibration resistance 10 to 55 Hz, 1.5-mm or 300m/s2 double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
Protective structure IEC 60529 IP67
Connection method Pre-wired (standard length: 2 m/500 mm)/M8 connector
Indicator lamp Operation indicator (orange), stability indicator (green) [Note that the emitter has the power indicator
(orange) only]
Weight
(Packed
state)
Pre-wired
models (with
2-m cable)
Approx. 120 g 65 g
Connector type 30 g Approx. 20 g
Material Case PBT (polybutylene terephthalate)
Lens Methacylate resin
Accessories Instruction manual (The Reflector or Mounting Bracket is not provided with any of the above models.)
11E3Z
Rating/performance
Diffuse-
reflective
Distance-
settable
Retro-reflective for PET bottles
(without MSR function)
Grooved-type
narrow-beam wide-beam
E3Z-L61/66 E3Z-LS61/66 E3Z-B61/66 E3Z-B62/67 E3Z-G61 E3Z-G62
E3Z-L81/86 E3Z-LS81/86 E3Z-B81/86 E3Z-B82/87 E3Z-G81 E3Z-G82
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
IEC 60529 IP67 IEC 60529 IP64
Pre-wired (standard length: 2 m/500 mm)/M8 connector Pull-out cable type (standard ca-
ble length: 2 m/500 mm) / connec-
tor relay type (standard cable
length: 300 mm
Operation indicator (orange), stability indicator (green) Operation indicator (orange)
Approx. 65 g 65 g
Approx. 20 g 30 g
PBT (polybutylene terephthalate) ABS
Methacylate
resin
Denaturated polyallylate Methacylate resin
Instruction manual (The Reflector or Mounting Bracket is not provided with any of the above models.)
12 Photoelectric Sensors
Characteristic data (typical)
Operating Range
Narrow-beam Retroreflective Models for transparent objects
E3Z-L E3Z-B#1/B#6 + E39-R1S
(optional reflector)
E3Z-B#2/B#7 + E39-R1S
(optional reflector)
Distance-setting
E3Z-LS [BGS] E3Z-LS [FGS]
Excess Gain vs. Distance
Through-beam Through-beam Retroreflective Models
E3Z-T#1(T#6) E3Z-T#AE3Z-R#1(R#6) + Reflectors
10
8
6
4
2
0
- 2
- 4
- 6
- 8
-10
8060
40 100 120 140 160
20
Distance X (mm)
Sensing object:
white paper (100 x 100 mm) Y
X
Distance Y (mm)
Y
X
50
40
30
20
10
0
-10
-20
-30
-40
-40
0.5 2.51 1.5 2
Distance X (m)
Reflector: E39-R1S
500-mm
Distance Y (mm)
Y
X
80
60
40
20
0
- 20
- 40
- 60
-80
2413
Distance X (m)
Reflector: E39-R1S
2-m type
Distance Y (mm)
8
6
4
2
0
-2
-4
-6
-8
50 100 150 200 250
X
YSet distance: 40 mm, 200 mm
Sensing object: White paper,
100 x 100 mm
200-mm setting
40-mm setting
Distance X (mm)
Operating range Y (mm)
20
15
10
5
0
-5
-10
-15
-20
200 400 600 800
X
Y
40-mm set distance
200-mm set distance
Distance X (mm)
Set distance: 40 mm, 200 mm
Sensing object: White paper,
100 mm x 100 mm
Operating range Y (mm)
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 102030405060
Distance X (m)
Excess gain ratio
Operating
level
1,600
1,400
1,200
1,000
800
600
400
200
010 20 30 40 50
Distance X (m)
Received light output (mV)
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10246810
Distance X (m)
E39-R3 E39-R1S
E39-R2
E39-R1
Excess gain ratio
Operating
level
13E3Z
Diffuse-reflective Diffuse-reflective Narrow-beam
E3Z-D#1(D#6) E3Z-D#2(D#7) E3Z-L
Retro-reflective for transparent objects
E3Z-B#1/B#6 + E39-R1S
(optional reflector)
E3Z-B#2/B#7 + E39-R1S
(optional reflector)
Distance vs. Size
Diffuse-reflective Diffuse-reflective Narrow-beam
E3Z-D#1(D#6) E3Z-D#2(D#7) E3Z-L
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 50 100 150 200 250 300
Distance X (m)
Sensing object: 300 x 300 mm white paper
Excess gain ratio
Operating
level
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 0.5 1 1.5 2 2.5
Distance X (m)
Sensing object: 300 x300 mm white paper
Excess gain ratio
Operating
level
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 50 100 150 200
Distance (mm)
Operation
level
Excess gain (factor)
0.5 1 1.5 2
Distance (m)
Receiver output
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
500-mm type
1234
Distance (m)
Receiver output
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
2-m type
350
300
250
200
150
100
50
350300250200150100500
Side length (one side) of sensing object: d (mm)
Distance (mm)
Black carbon
SUS (glossy surface)
White paper
d
d
4.5
4
3.5
3
2.5
2
1.5
1
0.5
350300250200150100500
Black carbon
White paper
d
d
Side length (one side) of sensing object: d (mm)
Distance (mm)
SUS (glossy surface)
200
180
160
140
120
100
80
60
40
20
120100806040200
Sensing object size (mm)
Distance (mm)
14 Photoelectric Sensors
Spot diameter vs. Distance
Narrow-beam Distance setting
E3Z-L E3Z-LS
Differential travel / Hysteresis vs. Distance
Narrow-beam Distance setting
E3Z-L E3Z-LS
Inclination Characteristics Short-distance Characteristics
Distance setting Distance setting
E3Z-LS E3Z-LS
Vertical Horizontal
6
5
4
3
2
1
1601401208040 10060200
Distance (mm)
Spot diameter (mm)
Spot diameter (mm)
Sensing object size (mm)
20
18
16
14
12
10
8
6
4
2
030025020015010050
30
25
20
15
10
5
150100500
Distance (mm)
Differential (mm)
10
9
8
7
6
5
4
3
2
1
250200150100500
White paper
Hysteresis differential (%)
Sensing distance (mm)
Black paper
-40 -30 -20 -10 0 10 20 30
-q
+q
20
15
10
5
0
-5
-10
-15
-20
40
Set distance: 40 mm, 200 mm
Sensing object: White paper,
100 mm x 100 mm
200-mm set distance
40-mm set distance
Vertical
Sensing
object Center
line
Inclination
-q
+q
Rate of sensing distance change (%)
Sensing object size (mm)
Center
line
20
15
10
5
0
-5
-10
-15
-20
-40 -30 -20 -10 0 10 20 30 40
200-mm set distance
Sensing
object
-q
Set distance: 40 mm, 200 mm
Sensing object: White paper,
100 mm x 100 mm
40-mm set distance
Horizontal
Inclination
+q
Rate of sensing distance change (%)
Sensing object size (mm)
250
200
150
100
50
0
Set distance: 40 mm
Set distance: 200 mm
40 mm
0 mm 9 mm
199 mm 185 mm
4 mm
36 mm
Sensing distance (mm)
Material
White paper White paper Black paper Black paper
15E3Z
FGS Mode Set Distance vs. Sensing Range
Distance setting
E3Z-LS
White Paper Black Paper
Sensing Distance vs. Material
Distance setting
E3Z-LS
At Set Distance of 40 mm At Set Distance of 200 mm
800
700
600
500
400
300
200
100
300250200150100500
Sensing range (mm)
Set distance (mm)
800
700
600
500
400
300
200
100
300250200150100500
Sensing range (mm)
Set distance (mm)
50
40
30
20
10
0
Sensing distance (mm)
Material
White
paper Veneer Card
board Black
paper Black
rubber SUS Mirror
surface
240
200
160
120
80
40
0
Sensing distance (mm)
Material
White
paper Veneer Card
board Black
paper Black
rubber SUS Mirror
surface
16 Photoelectric Sensors
Output Circuit Diagram
NPN output
Model Output transis-
tor Status Timing chart Mode selec-
tion switch Output circuit
E3Z-T61
E3Z-T66
E3Z-T61A
E3Z-T66A
E3Z-R61
E3Z-R66
E3Z-D61
E3Z-D66
E3Z-D62
E3Z-D67
E3Z-L61
E3Z-L66
E3Z-B61
E3Z-B62
E3Z-B66
E3Z-B67
E3Z-G61
Light ON L•ON
(LIGHT ON)
Dark ON D•ON
(DARK ON)
E3Z-LS61
E3Z-LS66
Light ON L•ON
(LIGHT ON)
BGS: Either leave the pink wire (2) open or connect it to the blue wire (3).
FGS: Connect the pink wire (2) to the brown wire (1).
Dark ON D•ON
(DARK ON)
Light ON L•ON
(LIGHT ON)
Dark ON D•ON
(DARK ON)
E3Z-G62
Light ON L•ON
(LIGHT ON)
Dark ON D•ON
(DARK ON)
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation
indicator
(orange)
(Between brown and black)
Output
transistor
Load
(Relay)
Through-beam receiver Retroreflective model Diffuse-reflective model
Connector Pin Arrangement
Note: Terminal 2 is not used.
4
1
24
3
3
112 to 24 VDC
Brown
BlackControl output
Blue
100 mA
max.
Operation
indicator
(orange)
Stability
indicator
(green)
0V
ZD
Load
(Relay)
Main
circuit
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
(Between brown and black)
Operation
indicator
(orange)
Output
transistor
Load
(Relay)
Through-beam emitter
Power
indicator
(orange)
Main
circuit
3
1
12 to 24
VDC
Brown
Blue
Connector Pin Arrangement
Note: Terminal 2 and 4 are not used.
1
24
3
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between brown and black)
1
24
3
4
2
1
3
Connector Pin Arrangement
12 to 24 VDC
Brown
Black
Control
output
Blue
100 mA
max.
Operation
indicator
(orange)
Stability
indicator
(green)
ZD
Load (Relay)
Main
circuit
Pink
FGS
BGS
0 V
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between brown and black)
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
VERY FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between brown and black)
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
VERY FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between brown and black)
(Between brown and black (white)
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
Control output
Output transistor
Load
(Relay)
12 to 24 VDC
0V
Load
(Relay)
Connector Pin arrangement
1
24
3
3
2
(Control output)
ZD
(S2)
White
100 mA
max.
Load
(Relay)
100 mA
max.
(S1) 4
1Brown
Operation
indicator
S 2 (orange)
Main
circuit
Operation
indicator
S 1
(orange)
Blue
(Control output)
ZD
Black
(Between brown and black (white)
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
Control output
Output transistor
Load
(Relay)
17E3Z
PNP output
Model Output transis-
tor Status Timing chart Mode selec-
tion switch Output circuit
E3Z-T81
E3Z-T86
E3Z-T81A
E3Z-T86A
E3Z-R81
E3Z-R86
E3Z-D81
E3Z-D86
E3Z-D82
E3Z-D87
E3Z-L81
E3Z-L86
E3Z-B81
E3Z-B82
E3Z-B86
E3Z-B87
E3Z-G81
Light ON L•ON
(LIGHT ON)
Dark ON D•ON
(DARK ON)
E3Z-LS81
E3Z-LS86
Light ON L•ON
(LIGHT ON)
BGS: Either leave the pink wire (2) open or connect it to the blue wire (3).
FGS: Connect the pink wire (2) to the brown wire (1).
Dark ON D•ON
(DARK ON)
Light ON L•ON
(LIGHT ON)
Dark ON D•ON
(DARK ON)
E3Z-G82
Light ON L•ON
(LIGHT ON)
Dark ON D•ON
(DARK ON)
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
(Between blue and black)
Operation
indicator
(orange)
Output
transistor
Load
(Relay)
Through-beam receiver Retroreflective model Diffuse-reflective model
Brown
Black
Blue
Control output
Operation
indicator
(orange)
Stability
indicator
(green)
ZD
Main
circuit
Connector Pin Arrangement
Note: Terminal 2 is not used.
4
1
3
12 to 24 VDC
100 mA
max.
0V
Load
(Relay)
1
24
3
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
(Between blue and black)
Operation
indicator
(orange)
Output
transistor
Load
(Relay)
Through-beam emitter
Power
indicator
(orange)
Main
circuit
3
1
12 to 24
VDC
Brown
Blue
Connector Pin Arrangement
Note: Terminal 2 and 4 are not used.
1
24
3
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between blue and black)
4
1
24
3
1
2
30 V
ZD
Connector Pin Arrangement
12 to 24 VDC
Brown
Black
Control
output
Blue
100 mA
max.
Operation
indicator
(orange)
Stability
indicator
(green)
Load (Relay)
Main
circuit
Pink
FGS
BGS
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between blue and black)
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
VERY FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between blue and black)
ON
OFF
ON
OFF
ON
OFF
NEAR FAR
VERY FAR
Operation
indicator
(orange)
Output
transistor
Load (e.g.
relay)
(Between blue and black)
(Between brown and black (white)
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
Control output
Output transistor
Load
(Relay)
Connector Pin arrangement
1
24
3
12 to 24 VDC
Load
(Relay)
0V
Blue
100 mA
max.
Load
(Relay)
2
3
1Brown
White
4Black
(Control output)
ZD
100 mA
max.
(Control output)
ZD
Main
circuit
Operation
indicator
S 2 (orange)
Operation
indicator
S 1
(orange)
(Between brown and black (white)
Incident
Interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
Control output
Output transistor
Load
(Relay)
18 Photoelectric Sensors
Connectors (Sensor I/O connectors)
Brown
White
Blue
Black
Wire
colors
XS3F-M421-402-A
XS3F-M421-405-A
XS3F-M422-402-A
XS3F-M422-405-A
2
4
1
3
1
2
3
4
Class Wire, outer jacket
color
Connector pin
No.
Application
Standard E3Z-LS E3Z-G62/82
For DC
Brown APower supply (+V)
White B--- BGS / FGS
selection
Output 2
(S2)
Blue CPower supply (0 V)
Black DOutput Output 1
(S1)
19E3Z
Nomenclature:
Distance-setting
E3Z-LS##
Operation
Slit for through-beam model (Optional accessory:
E39-S65A/B/C/D/E/F)
BGS / FGS Application for distance setting E3Z-LS
Through-beam
E3Z-T## Receiver
E3Z-T##A Receiver
Retroreflective Models
E3Z-R##
E3Z-B##
Diffuse-reflective
E3Z-D##
E3Z-L##
Stability indicator
(green)
Operation selector
Operation indicator
(orange)
Sensitivity adjuster
Stability indicator
(green)
Operation selector
Operation indicator
(orange)
Set distance adjuster
(5-turn endless
adjustment)
Mounting method
1. Hook the upper protruding
portions of the Slit to the up-
per indented mounting por-
tion of the Sensor and
adjust the position of the
Slit so that the Slit will be
parallel to the lens surface.
2. Press the lower protruding
portion of the Slit onto the
indented mounting portion
of the Sensor until the Slit
snaps in.
Mounting condition
Demounting method
1. Press the upper portion of
the Slit.
2. Disconnect the lower pro-
truding portion of the Slit
from the Sensor and re-
move the Slit.
(Slit) (Sensor)
Hook
Protruding
portion
Upper indented
mounting portion
Lower mounting
dent portion
Slit Sensor
(1)
(2)
Side view Front view
(1)
(2)
Simple Detection of Glossy, Uneven Objects
BGS
(Background Suppression)
Objects beyond the set distan-
ce, such as the conveyor, will
not be detected. The hystere-
sis is 10% or less, so at a set
distance of 40 mm, steps with
a thickness of 4 mm can be de-
tected on objects.
Selectable by Changing Cable Connection
Distance threshold
ON (incident)
OFF (interrupted)
Conveyor (background)
(for Light-ON setting)
FGS
(Foreground Suppression)
Glossy, uneven objects are re-
liably detected because the
OFF (incident) status occurs
only when the conveyor is de-
tected, and ON (interrupted)
status occurs only when an ob-
ject exists or when reflected
light is not returned to the Sen-
sor. (Depending on the shape
of the object, an OFF-delay
timer may be required.)
(for Dark-ON setting)
Distance threshold
Light level threshold
(fixed)
ON (interrupted)
OFF
(incident)
Conveyor (background)
ON (interrupted)
L/ON
Stability
(green)
Stability
(green)
Stability
(green)
Stability
(green)
L/ON
Operation
(orange)
Operation
(orange)
Operation
(orange)
Operation
(orange)
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
FGS
D/ON
D/ON
NEAR region
Stable NEAR
Stable FAR
Very insufficient
incident light
FAR region
Unstable NEAR Unstable FAR
VERY FAR region
(for FGS only)
Distance threshold
(settable)
Incident light level threshold
(not settable)
Not sufficient incident
light margin
Slightly insufficient
incident light
BGS
20 Photoelectric Sensors
Precautions
Do not connect an AC power supply to the Sensor. If AC pow-
er (100 VAC or more) is supplied to the Sensor, it may ex-
plode or burn.
Be sure to abide by the following precautions for the safe op-
eration of the Sensor.
Wiring
Power Supply Voltage and Output Load Power Supply Volt-
age
Make sure that the power supply to the Sensor is within the
rated voltage range. If a voltage exceeding the rated voltage
range is supplied to the Sensor, it may explode or burn.
Load Short-circuiting
Do not short-circuit the load, otherwise the Sensor may be
damaged.
Connection without Load
Do not connect the power supply to the Sensor with no load
connected, otherwise the internal elements may explode or
burn.
Operating Environment
Do not use the Sensor in locations with explosive or flamma-
ble gas.
Design
Power Reset Time
The Sensor is ready to operate 100 ms after the Sensor is
turned ON. If the load and Sensor are connected to indepen-
dent power supplies respectively, be sure to turn ON the Sen-
sor before supplying power to the load.
Wiring
Avoiding Malfunctions
If using the Photoelectric Sensor with an inverter or servomo-
tor, always ground the FG (frame ground) and G (ground) ter-
minals, otherwise the Sensor may malfunction.
Mounting
Mounting the Sensor
• If Sensors are mounted face-to-face, make sure that the op-
tical axes are not in opposition to each other. Otherwise,
mutual interference may result.
• Always install the Sensor carefully so that the aperture an-
gle range of the Sensor will not cause it to be directly ex-
posed to intensive light, such as sunlight, fluorescent light,
or incandescent light.
• Do not strike the Photoelectric Sensor with a hammer or
any other tool during the installation of the Sensor, or the
Sensor will lose its water-resistive properties.
• Use M3 screws to mount the Sensor.
• When mounting the case, make sure that the tightening
torque applied to each screw does not exceed 0.54 Nm.
M8 Connector
• Always turn OFF the power supply to the Sensor before
connecting or disconnecting the metal connector.
• Hold the connector cover to connect or disconnect it.
• Secure the connector cover by hand. Do not use pliers, oth-
erwise the connector may be damaged.
• If the connector is not connected securely, it may be discon-
nected by vibration or the proper degree of protection of the
Sensor may not be maintained.
Distance setting models E3Z-LS
• Make sure that the sensing side of the Sensor is parallel
with the surface of the sensing objects. Normally, do not in-
cline the Sensor towards the sensing object.
If the sensing object has a glossy surface, however, incline
the Sensor by 5° to 10° as shown in the illustration, provided
that the Sensor is not influenced by background objects.
• If there is a mirror-like object below the Sensor, the Sensor
may not operate stably. Therefore, incline the Sensor or
separate the Sensor from the mirror-like object as shown
below.
! Caution
Correct Use
Sensing side
Surface of sensing object
Glossy object
Mirror-like object
Sensing object
21E3Z
• Do not install the Sensor in the wrong direction. Refer to the
following illustration.
Install the Sensor as shown in the following illustration if
each sensing object greatly differs in color or material.
Adjustments-indicator operation
Note: 1 . If the stability indicator is lit, the detection/no detection status is stable
within the rated ambient operating temperature (-25 to 55°C).
2 . The VERY FAR region is supported only for FGS. The incident light
threshold is fixed and cannot be set. The distance to the incident light
threshold depends on the color and gloss of the sensing object’s sur-
face.
Retro-reflective for transparent objects E3Z-B
Design
Bottles
The Sensor may be unable to achieve stable detection depen-
ding on the shape of bottles. Be sure to verify stable detection
before using the Sensor.
Mounting
Sensor Mounting
If the Sensor fails to provide stable detection due to the shape
of bottles, adjust the location and inclination of the Sensor.
Inspection and Maintenance
Cleaning
Never use paint thinners or other organic solvents to clean the
surface of the product.
Moving direction
Moving direction
Moving direction
Sensing
object
Sensing
object
Sensing
object
Moving direction
Moving direction
L/ON
Stability
(green)
Stability
(green)
Stability
(green)
Stability
(green)
L/ON
Operation
(orange)
Operation
(orange)
Operation
(orange)
Operation
(orange)
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
FGS
D/ON
D/ON
NEAR region
Stable NEAR
Stable FAR
Very insufficient
incident light
FAR region
Unstable NEAR Unstable FAR
VERY FAR region
(for FGS only)
Distance threshold
(settable)
Incident light level threshold
(not settable)
Not sufficient incident
light margin
Slightly insufficient
incident light
BGS
22 Photoelectric Sensors
Dimensions (Unit: mm)
Sensors
Through-beam
Pre-wired
E3Z-T61
E3Z-T81
E3Z-T61A
8
17
2.1
25.4
Vinyl-insulated round cable with two conductors, 4 dia.
(0.2 mm² with 1.1-dia. insulator); standard length: 2 m
2-M3
31
15.5
Optical axis
11
18
10.410.8
Power indicator
(orange)
Lens
7.2
Emitter
M12 x1
1
3
2
4
Vinyl-insulated round cable
with two conductors, 4 dia.;
standard length: 0.3 m
Terminal No.
Specifications
1+V
2 ---
30V
4 ---
Note: Terminal 2 and 4
are not used.
Connector relay models
E3Z-T61-M1J
B,D are free terminals.
Termi-
nal No.
Specifica-
tions
1+V
2 ---
30V
4 ---
Model CAD file
E3Z-T61-L
E3Z-T81-L E3Z_01
M12 x 1
1
3
2
4
Vinyl-insulated round cable
with three conductors, 4 dia.;
standard length: 0.3 m
Terminal No.
Specifications
1+V
2 ---
30V
4 Output
Note: Terminal 2 is not used.
Connector relay models
E3Z-T61-M1J
17
2.1
25.4
Vinyl-insulated round cable with three conductors, 4 dia.
(0.2 mm² with 1.1-dia. insulator); standard length: 2 m
2-M3
31
15.5
Optical axis
11
18
20
12.45
8.8
3.2
Stability indicator (green)
Operation indicator
(orange)
10.410.8
4.3
Sensing adjuster
Operation selector
Lens
7.2
Receiver
Model CAD file
E3Z-T61-L
E3Z-T81-L E3Z_02
B is a free terminal.
Termi-
nal No.
Specifica-
tions
1+V
2---
30V
4 Output
Through-beam
Connector type
E3Z-T66
E3Z-T86
E3Z-T66A 17
2.1
25.4
M8
connector
31
10.4 2-M3
15.5
7.2
Lens
Optical axis
11
18
20 8
10.410.8
Power indicator
(orange)
9.75
Emitter
Model CAD file
E3Z-T66-L
E3Z-T86-L E3Z_04
Model CAD file
E3Z-T66-D
E3Z-T86-D E3Z_05
17
2.1
25.4
M8
connector
9.75
31
10.4
15.5
Lens
Optical axis
11
18
20
12.45
8.8
3.2
Stability indicator (green)
Operation indicator
(orange)
10.410.8
4.3
Sensing adjuster
Operation selector
7.2
2-M3
Receiver
(=
5HWURUHIOHFWLYH0RGHOV
3UHZLUHG
(=%
(=%
(=%
(=%
(=5
(=5
'LIIXVHUHIOHFWLYH
3UHZLUHG
(='
(='
(='
(='
(=/
(=/
M12 x 1
1
3
2
4
Vinyl-insulated round cable
with three conductors, 4 dia.;
standard length: 0.3 m
Terminal No.
Specifications
1+V
2 ---
30V
4 Output
Note: Terminal 2 is not used.
Connector relay models
(E3Z-###-M1J)
20
12.45
8.8
3.2
Stability indicator (green)
Operation indicator (orange)
17
2.1
25.4
Vinyl-insulated round cable with three conductors, 4 dia.
(0.2 mm² with 1.1-dia. insulator); standard length: 2 m
2-M3
31
15.5
Two, 7-dia.
lenses
Receiver
Optical axis
Emitter
4
18 4
10.410.8
4.3
Sensing adjuster
Operation selector
&$'ILOH (=B
BLVDIUHHWHUPLQDO
7HUPL
QDO1R
6SHFLILFD
WLRQV
9

9
2XWSXW
5HWURUHIOHFWLYH0RGHOV
&RQQHFWRUW\SH
(=%
(=%
(=%
(=%
(=5
(=5
'LIIXVHUHIOHFWLYH
&RQQHFWRUW\SH
(='
(='
(='
(='
(=/
(=/
20
12.45
8.8
3.2
Stability indicator (green)
Operation indicator (orange)
17
2.1
25.4
M8 connector
31
10.4
15.5
Two, 7-dia.
lenses
Receiver
Optical axis
Emitter
4
18 4
10.410.8
4.3
Sensing adjuster
Operation selector
9.75
2-M3
&$'ILOH (=B
'LVWDQFHVHWWDEOH0RGHOV
3UHZLUGHPRGHOV
(=/6
(=/6
4.3
8
12.7
20
10.8 10.4
17
3118 4
4
25.4
2.1
13.5
Operation indicator
(orange)
Operation selector
Set distance adjuster
Stability indicator (green)
2 lenses (7 dia.)
Receiver
Optical axis
Emitter Two, M3
4-dia, 4-core vinyl-insulated round cable
(conductor cross-sectional area: 0.2 mm²;
insulation diameter: 1.1 mm)
Standard length: 2 m / 0.5 m
24 Photoelectric Sensors
Accessories (Order Separately)
Distance-settable Models
Connector type
E3Z-LS66
E3Z-LS86 4.3
8
12.7
20
10.8 10.4
17
31
10.4
18 4
4
25.4
2.1
13.5
9.75
Operation indicator
(orange)
Operation selector
Set distance adjuster
Stability indicator (green)
2 lenses (7 dia.)
Receiver
Optical axis
Emitter Two, M3
S2
S1
Operation Mode Selector
Note: 1. It is in a reflection side.
2. Both 1 and 2-axis models have S1; only 2-axis models have S2.
S1 output: black
S2 output: white
36
20
40
Operation indicator (orange)
257.511
40
19
9
35
50
"Vinyl-insulated round cable of 4 dia. 4 cores conductor
cross-sectional area: 0.2mm
2
; insulation diameter: 1.1mmStandard length: 2 m, 0.5 m"
Two, 4.5 dia.
Optical axis S1 * Optical axis S2 *
"4-dia., 4-core vinyl-insulated
round cableStandard length: 0.3 m"
M8
2z
13
Junction connector
(E3Z-G6#-M3J)
CAD file E3Z_10
Grooved-type Models
E3Z-G
Slits
E39-S65A
E39-S65B
E39-S65C
A
32.2
4.5
3.4
0.2
15.5
10.4
E39-S65A 0.5-mm dia. Stainless
steel
(SUS301)
E39-S65B
E39-S65C
Model Dimension
AMaterial
1.0-mm dia.
2.0-mm dia.
Model Dimension
AMaterial
E39-S65A 0.5-mm dia. Stainless
steel
(SUS301)
E39-S65B 1.0-mm dia.
E39-S65C 2.0-mm dia.
Slits
E39-S65D
E39-S65E
E39-S65F A
32.2 10
4.5
3.4
0.2
15.5
10.4
E39-S65D 0.5 Stainless
steel
(SUS301)
E39-S65E
E39-S65F
Model Dimension
AMaterial
1.0
2.0
Model Dimension
AMaterial
E39-S65D 0.5 Stainless
steel
(SUS301)
E39-S65E 1.0
E39-S65F 2.0
Cat. No. E701-E2-01 In the interest of product improvement, specifications are subject to change without notice.
OMRON EUROPE B.V.
Wegalaan 67-69,
NL-2132 JD, Hoofddorf,
The Netherlands
Phone:+31 23 568 13 00
Fax:+31 23 568 13 88
www.eu.omron.com